Edge-Core RPS600WA Installation Guide

thereisnoedgelimitthereisnopermanentcorethereisnoedgelimitthereisnopermanentcoreExternal Redundant Power SupplyInstallation Guide

viiiEnvironmental StatementThe manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production

ixContentsChapter 1: About the Redundant Power Supply 1-1Overview 1-1Features and Benefits 1-1Front and Rear Panels 1-2LEDs 1-2Supported Switches

xTablesTable 1-1 Port Status LEDs 1-3Table 1-2 System LEDs 1-3Table 1-3 Supported Switch 1-4Table A-1. Troubleshooting Chart A-1

xiFiguresFigure 1-1 Front and Rear Panels 1-2Figure 1-2 LEDs 1-2Figure 2-1. Attaching the Brackets 2-3Figure 2-2. Installing the RPS in a Rack 2-3

xiiFigures

1-1Chapter 1: About the Redundant Power SupplyOverviewThis External Redundant Power Supply (RPS) can supply 600 Watts of backup power to four switches

About the Redundant Power Supply1-21Front and Rear PanelsFour power indicators and one fan indicator are located on the RPS’s front panel. While the A

LEDs1-31Table 1-1 Port Status LEDsLED (1-4) Condition StatusLink Off The port does not have a valid connection to a switch.On Yellow The port has a v

About the Redundant Power Supply1-41Supported SwitchesTable 1-3 Supported SwitchSwitches with 14-pin RPU connector on rear panel.ES3526VES3526V 1ES35

2-1Chapter 2: Installing the Redundant Power SupplyInstallationThe RPS may be placed on a desktop or mounted in a rack. Caution: DO NOT place the RPS

Installing the Redundant Power Supply2-22Equipment ChecklistAfter unpacking the RPS, check the contents to be sure you have received all the component

Mounting2-32To rack-mount devices:1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.Figure 2-1. Attaching th

Installing the Redundant Power Supply2-42liegt. (Siehe "Temperatur" auf Seite C-1.)• Mechanische Last: Stellen Sie kein Gerät auf eine Rack

Connecting Switches to the RPS2-52Connecting Switches to the RPSCaution: DO NOT connect the RPS to an AC power source until DC power cords have been c

Installing the Redundant Power Supply2-62Figure 2-5. RPS Supporting Four SwitchesNote: For International use, you may need to change the AC line cord

A-1Appendix A: TroubleshootingDiagnosing RPS Indicators Table A-1. Troubleshooting ChartSymptom ActionPower LED is Off • Internal power supply is dis

TroubleshootingA-2APower and Cooling ProblemsIf the PWR LED does not turn on when the power cord is plugged in, you may have a problem with the power

B-1Appendix B: SpecificationsPhysical CharacteristicsPorts4 RPS DC power outlets (IEC socket 216C743-07)LEDs Port: Link, ActivitySystem: Power, Fan, T

SpecificationsB-2BOvercurrent ProtectionPorts are shutdown when output exceeds 14.5 AOver-voltage ProtectionPorts are shutdown when output exceeds 12.

Index-1Aadhesive feet, attaching 2-4air flow requirements 2-1Bbrackets, attaching 2-3CcompliancesEMC B-2safety B-2contents of package 2-2cooling probl

Installation GuideExternal Redundant Power Supplywith 4 Independent Redundant Power Supply Ports

IndexIndex-2

RPS600WA-38E012005-R01150000046600A

RPS600WA-38E012005-R01150000046600A

iiiCompliancesFCC - Class BThis equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with th

ivCE Mark Declaration of Conformance for EMI and Safety (EEC)This information technology equipment complies with the requirements of the Council Direc

vThis unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transforme

viVeuillez lire à fond l'information de la sécurité suivante avant d'installer le RPS:AVERTISSEMENT: L’installation et la dépose de ce group

viiBitte unbedingt vor dem Einbauen des RPS die folgenden Sicherheitsanweisungen durchlesen:WARNUNG: Die Installation und der Ausbau des Geräts darf n